玻璃纤维-铝合金层合板氙灯老化性能研究

目的研究氙灯环境对玻璃纤维-铝合金层合板性能的影响。方法通过研究玻璃纤维-铝合金层合板在氙灯老化后的力学性能、基体红外光谱、铝合金表面形貌及元素变化,分析层合板的氙灯老化机理。结果随氙灯老化时间的延长,树脂基体老化降解程度越高,树脂与纤维、铝合金的界面强度下降,使材料拉伸及弯曲性能降低,拉伸强度受老化影响最为显著的是正交结构层合板,老化84 d后强度降低13.7%,正交结构0°方向层合板的弯曲强度受氙灯老化影响降低4.6%,其他试样的弯曲强度降幅均低于5%,氙灯老化后的铝合金层表面的微凹坑数量及尺寸无明显变化,但凹坑氧元素随老化周期延长略微增加。结论氙灯环境主要影响玻璃纤维-铝合金层合板中的复合材料层及各界面,树脂基体的降解导致力学性能的衰退,而对于铝合金的影响并不明显。     

Air Pollution and Heat Exposure Study in the Workplace in a Glass Manufacturing Unit in India

Air pollution in the workplace environment due to industrial operation have been found to cause serious occupational health hazard. Similarly, heat stress is still most neglected occupational hazard in the tropical and subtropical countries like India. The hot climate augments the heat exposure close to sources like furnaces. In this study an attempt is made to assess air pollution and heat exposure levels to workers in the workplace environment in glass manufacturing unit located in the State of Gujarat, India. Samples for workplace air quality were collected for SPM, SO₂, NO₂ and CO₂ at eight locations. Results of workplace air quality showed 8-hourly average concentrations of SPM: 165–9118 μg/m³, SO₂: 6–9 μg/m³ and NO₂: 5–42 μg/m³, which were below the threshold limit values of workplace environment. The level of CO₂ in workplace air of the plant was found to be in the range 827–2886 μg/m³, which was below TLV but much higher than the normal concentration for CO₂ in the air (585 mg/m³). Indoor heat exposure was studied near the furnace and at various locations in an industrial complex for glass manufacturing. The heat exposure parameters including the air temperature, the wet bulb temperature, and the globe parameters were measured. The Wet Bulb Globe Temperature (WBGT), an indicator of heat, exceeded ACGIH TLVs limits most of the time at all the locations in workplace areas. The recommended duration of work and rest have also been estimated.     

改性乙二醛-水玻璃化学灌浆材料的研究

研究了一种改性乙二醛一水玻璃化学灌浆材料，其胶凝时间可由乙二醛的加入量控制．抗压强度大．表面活性剂甲的加入可以有效提高其渗透性。     

海水环境下玻璃纤维增强复合材料力学性能演化规律研究

目的 研究海水环境下海流能发电机组叶片用玻璃纤维复合材料力学性能的变化规律.方法 在实验室内通过海水浸泡试验、拉伸试验、弯曲试验以及剪切试验,测定叶片用玻璃纤维树脂基复合材料的吸水特性,以及在人工海水介质中各项力学性能参数的演变规律.结果 随着浸泡时间的增加,玻璃纤维树脂基复合材料吸水率先逐步增大、后趋于稳定,总吸水率约0.075％.抗拉强度呈先降低、后提高、又降低的趋势,抗拉强度最高可超过1100 MPa,最小值约为940 MPa.弹性模量和弯曲强度呈逐渐降低的趋势,弹性模量降幅约9.5％,弯曲强度降幅约为30％.弯曲模量变化起伏不定,变化幅度在15％以内.材料剪切强度呈先增大、后降低的趋势,最小值为189 MPa,较初始值高10 MPa.剪切模量呈先降低、后提高的现象,在浸泡28 d时,剪切模量最小,为16.4 GPa.结论 玻璃纤维增强树脂基复合材料经过长期海水浸泡后,拉伸及抗剪切性能略有降低,但降幅不大,抗弯性能下降明显,需要在叶片结构设计和强度计算时,充分考虑抗弯性能衰减的负面影响.     

Test for the effects of three surfactants on the penetration ability of the calcium chloride and water glass solutions in dust

１ＩｎｔｒｏｄｕｃｔｉｏｎＣａｌｃｉｕｍｃｈｌｏｒｉｄｅｉｓｏｆｔｅｎｕｓｅｄｉｎｔｈｅｆｉｅｌｄｏｆｓｏｉｌｓｔａｂｉｌｉｚａｔｉｏｎａｎｄｒａｉｓｉｎｇｄｕｓｔｃｏｎｔｒｏｌｂｅｃａｕｓｅｉｔｃａｎｒｅａｃｔｗｉｔｈｗａｔｅｒｇｌａｓ（Ｗｕ，１９...     

含硫污水系统耐蚀材料的筛选与应用

针对西北地区一综合炼油厂含硫污水管线的严重腐蚀问题，分析了腐蚀原因，确立了材料筛选方案，通过实验室静态挂片试验绘制了重量损失率变化曲线和现场挂片等试验手段，筛选推荐出了树脂玻璃钢耐蚀材料。工业生产应用结果表明，MFE-2型树脂玻璃钢是适用于该厂含硫污水系统的耐蚀材料，为类似装置的长周期运行提供了借鉴和经验。     

过滤捕集法处理含DEP雾废气的研究

为了探讨玻璃纤维过滤器处理含DEP雾废气的效率问题,在实验室进行了DEP雾去除实验。考查了不同气体入口浓度、过滤流速下玻璃纤维过滤捕集装置对含DEP雾废气的净化能力,结果表明:利用玻璃纤维过滤器去除DEP雾,在DEP雾粒径主要分布为0.48～3.4μm之间,DEP雾浓度小于220 mg/m3,过滤流速小于10 cm/s情况下,玻璃纤维过滤器对DEP雾的去除率大于99%,最大气体流量下的压力降小于1610Pa;同时对含油(酸)雾废气除雾效果好,特别是对于粒径特别细微的油(酸)雾,捕集效率也很高,还可回收利用,不会产生二次污染。     

检测管法与纳氏试剂光度法测定氨氮的比较研究

对氨氮真空玻璃检测管法和纳氏试剂光度法进行检出限、精密度、准确度,以及实际样品测试方面的比较研究。研究表明,氨氮检测管的检出限为0．2mg／L,精密度测定的相对标准偏差为0％～5．75％,准确度测定的加标回收率为93％～124％。检测管法和纳氏剂法同时测定多种实际样品,结果两种方法的相对误差为-37．8％～11．8％,结论：检测管法能够满足半定量测试的需求。     

Experimental study of recycling lightweight concrete with aggregates containing expanded glass

The focus is on the issue of waste management when constructing and recycling lightweight concrete (LWC) with aggregates containing expanded glass. The paper analyses the recycling of concrete from lightweight aggregates, and on the important issue of environmental and waste management. The characteristics of recycling LWC such as density, compressive strength and thermal conductivity are investigated, and compared with normal existing concrete from lightweight aggregates. The results indicate that it is possible to recycle lightweight concrete construction waste. The described method shows great possibilities for increasing the use of construction waste materials from LWC containing expanded glass, in order to benefit from better use of the available capacity from existing construction waste. The characteristics of density, compressive strength and thermal conductivity from the new recycled material were compared with normal existing concrete from lightweight aggregates, such as changes in dependency on the type and parts of waste as well as its new binding components. Thus, a new recycled material has been created with new characteristics of density, compressive strength and thermal conductivity, which is conform to the compressive strength class and rules on heat protection and energy efficiency use in buildings (SI OJ RS No. 42/2002). Laboratory density, compressive strength, and thermal conductivity tests results showed that LWC can be produced by the use of waste LWC with aggregates containing expanded glass. However, the use of waste LWC with aggregates containing expanded glass seems to be necessary for the production of cheaper and environmentally friendly LWC.     

某钢厂烧结烟气脱硫系统滤袋失效原因分析

分析了聚苯硫醚自身特性,从而了解目前烧结烟气脱硫系统袋式除尘器中选择其作为滤料的原因。并就目前某钢厂烧结烟气脱硫系统实际发生的滤袋失效问题,通过扫描电镜、EDS能谱分析及烧失量实验对滤袋进行分析,发现材料中混入的玻璃纤维是造成其失效的主要原因,为今后实际工程中滤袋的选择提供依据,从而尽量减少不必要的损失,确保烟气脱硫项目的正常运行。